<th id="u7p1p"><option id="u7p1p"></option></th>

      <object id="u7p1p"></object>

      <object id="u7p1p"><nobr id="u7p1p"></nobr></object>
      1. <tr id="u7p1p"></tr>
          <object id="u7p1p"></object>
            <object id="u7p1p"></object>
            <thead id="u7p1p"><option id="u7p1p"></option></thead>
            騰龍客服電話-173O883O666 _騰龍客服電話-173O883O666
            當前位置: 返回首頁 > 產品展示 > 攪拌車 >







            PM 施維英 CIFA 配件


            • 產品名稱:


            • 產品描述:
            • 相關標簽:



            混凝土攪拌車Concrete mixer

            混凝土攪拌車簡介:Brief Introduction of Concrete Mixer


            Jeddah Heavy Industries 3, 4, 5, 6 and 8 small concrete mixer trucks adopt mixing barrel tank structure, double helix curved blades and different blades in different cone sections, which improves the quality of concrete mixing, reduces the surplus, fully riveted frame, strong and durable; thicker, wider leaf springs, flexible, small footprint, especially suitable for urbanization garden greening, urban and rural construction, urban and rural construction. Construction work is carried out under various conditions such as roads and bridges.

            使用注意事項:Use precautions





            5、在施工現場卸料完畢后,應立即用攪拌車隨帶的軟管沖洗進料斗、出料斗、卸料溜槽等處,   粘附在車身各處的污泥及混凝土。在返回攪拌站的途中,應向攪拌筒內注150---200L水以清洗筒壁及葉片粘結的混凝土殘渣。


            7、  攪拌筒內外積污及殘存的混凝土渣塊時,以及在機修人員進入筒內進行檢修和焊補作業時,需先關閉汽車發動機,使攪拌筒   停止轉動。在機修人員進入筒內工作期間,   保證拌筒內通風良好,空氣新鮮,無可然氣體及有害灰塵,氧氣供應充足(不得使用純氧)。在筒內使用電動工具操作時,操作人員需有良好的絕緣保護。



            10、貫徹各項有關   操作規范?;炷翑嚢柽\輸車司機需經過培訓,無合格證者不得上崗操作。


            1. The pressure of the hydraulic system shall conform to the stipulations in the instructions for use and shall not be adjusted at will. The oil quality and quantity of hydraulic oil should meet the original requirements.

            2. Before loading concrete trucks, the residual water and debris in the mixing drum should be removed first. In the course of transportation, it is necessary to keep turning in order to prevent concrete segregation. Before the concrete mixer truck arrives at the site and unloads, it should first rotate the mixer at full speed of 14-18 rpm/min for 1-2 minutes, and then reverse unloading.  Before inversion, the mixing drum should be stabilized.

            3. The ambient temperature is higher than + 25 degrees Celsius, and the duration from loading, transportation to unloading shall not exceed 60 minutes. The ambient temperature shall be lower than + 25 degrees Celsius, and the above-mentioned time shall not exceed 90 minutes.

            4. In winter construction, we should check whether ice is frozen before start-up, remove residual water in mixing drum and water supply system seriously after work, close pump switch and put control handle in "stop" position.

            5. After discharging at the construction site, the hose attached to the mixer should be used to flush the hopper, hopper, chute and other places immediately, and the sludge and concrete adhering to the body everywhere. On the way back to the mixing station, 150 - 200 L of water should be injected into the mixing drum to clean the concrete residue adhering to the wall and blades of the drum.

            6. At the end of each day's work, the driver shall be responsible for injecting clean water into the mixing drum and rotating it at a high speed (14-18 rpm) for 5-10 minutes, then draining the water to ensure the cleanliness of the drum. When cleaning each part of the mixing drum with high-pressure water, attention should be paid to avoid the parts such as instruments and joysticks. The distance between the pressure water nozzle and the body paint surface shall not be less than 40 cm.

            7. When the contamination inside and outside the mixing drum and the residual concrete slag block are accumulated, and when the mechanic repairman enters the drum for repair and welding, the automobile engine should be shut down first to stop the rotation of the mixing drum. During the working period when the mechanic personnel enter the drum, ensure that the air in the drum is well ventilated, fresh, no natural gas and harmful dust, and the oxygen supply is sufficient (pure oxygen is not allowed to be used). Operators have good insulation protection when using electric tools in cylinders.

            8. When working, the hand shall not be put into the rotating mixing drum. It is strictly forbidden to extend the hand into the connecting part of the main discharge chute and the lengthening discharge chute in order to avoid accidents.

            9. The wear of mixing blades should be checked regularly and repaired and renewed in time.

            10. Implementing all relevant operational specifications. Drivers of concrete mixer trucks are not allowed to work without qualified certificates after professional training.

            Technical Support Hotline: 0317-6613888

            石家莊3立方攪拌車 鄭州3立方攪拌車 



            ???? 公安備案號:13092402000124

            Copyright ? 2019 - 2020 吉達重工 All Right Reserved.


            <th id="u7p1p"><option id="u7p1p"></option></th>

              <object id="u7p1p"></object>

              <object id="u7p1p"><nobr id="u7p1p"></nobr></object>
              1. <tr id="u7p1p"></tr>
                  <object id="u7p1p"></object>
                    <object id="u7p1p"></object>
                    <thead id="u7p1p"><option id="u7p1p"></option></thead>